How To Install A Reverse Osmosis System
Commissioning an osmosis system is a very easy operation. You will indeed have the choice to do it yourself (Do It Yourself) or to call in a professional. However, if you want to save money, it is recommended to do it yourself. To get there, you will need to follow the steps below.
Preparing The Device
This phase will allow you to properly equip your reverse osmosis unit. It will be important to properly mount all of the elements of your reverse osmosis unit. You will therefore have to restructure it. You will thus put in place the prefilters and the reverse osmosis membrane, without forgetting the filter station. If you seem lost, you can rely on the device’s user guide.
How To Install A Reverse Osmosis System Preparation
Here, it is a question of setting up all your water intake device . It is this junction which will allow you to connect your tap to your reverse osmosis unit. Once you have connected it properly, you can then tackle your dirty water pipe or orifice.
Mounted under the sink, this pipe will allow you to directly expel this dirty water. To install this component, you will first need to fix the flange and its gasket. Then screw your drain hose securely. Finally finish this phase by installing your tank on a tripod that you will place under your sink.
In the case of an aquarium reverse osmosis unit, you will simply have to check that all of your previous accessories are connected to it using a specific adapter. In addition, it is also very important to ensure that your aquarium reverse osmosis unit is fixed in a position that will allow anyone to admire its beautiful little aquatic landscape.
Installation Of Your Reverse Osmosis System
After having brilliantly carried out all the previous previous steps, you can then take care of the tap. To do this, make a hole with a diameter of about 12 mm and using a nut, fix your tap.
Below the tap, connect your reverse osmosis unit directly. Then put the device in a cupboard under the sink. In the case of an aquarium reverse osmosis unit, you must be careful not to break your glass.
Classic Installation
So here are a few steps how you can install an osmosis unit and all its devices, both in your kitchen and on your aquarium.
How To Test An Osmosis System?
Once your osmosis is in place, you can test it. It is a very important operation which will allow you to know if your installation system really works. To get there, you will first need to restore your water source by opening the valve that allows you to supply your reverse osmosis unit.
Then you can open your tap and let the water run for a few minutes. Once this is done, close the valve. During this period, you will have to wait for your reverse osmosis tank to fill up.
After this operation, you will finally open the draw-off tap to completely drain your reverse osmosis unit. If you miss something, you can see where the problem is and you can fix it.
How To Test The Quality Of The Water Leaving The Reverse Osmosis ?
As soon as your osmosis unit is in place, it is important to check the quality of the water that will come out. To do this, you will need to use a TDS (Total Dissolved Solids) tester . TDS is nothing more than a mixture of inorganic salts and some organic matter.
Once your TDS tester in hand, you must first let your osmosis water run in a glass for a maximum of 30 seconds. Then immerse your TDS tester in said glass. Stir your RO water and wait for a maximum of 10 seconds.
This little moment is useful because, for a successful test, your osmosis water will have to remain very calm. After that, you will have to note and compare the value that will be given to you by the TDS tester.
Once all this is done, repeat the operation a maximum of 6 times in succession with a glass that contains raw water. These values will allow you to appreciate the state of purity of your RO water.
Obtained as a percentage, this result can be interpreted in two ways. If it is less than 10%, it means that your membrane is not saturated and that your water is pure . If the latter is rather higher than 10%, you will know that your membrane is saturated and that your water is no longer pure.
How To Maintain It?
To enjoy the services of a device for a long time, it is important to maintain it properly. To use a water reverse osmosis longer, you will have to maintain it continuously as described in the following points.
Perform a weekly emptying of the tank of your reverse osmosis unit: this involves completely emptying the tank of your reverse osmosis unit by simply opening the tap located on your sink.
Check the pressure of your tank: carried out following the previous point, you will have to check that this pressure is around 0.4 bar.
Carry out an annual maintenance of your reverse osmosis unit: dismantle and restructure your entire reverse osmosis unit and repeat the TDS test.
Change your filters periodically: whether they are composed of active carbon or other elements, you are called upon to renew them.
In addition, you will also need to make sure to change the membrane of your reverse osmosis unit . With such actions, you will be able to use your reverse osmosis unit without any difficulty for a long time.
